Nasa

The AIS Engine 3 is supplied with a free copy of ‘SeaClear’ and a trial version of Software on Board. A data cable to connect to the 9 pin serial port of a PC and a 12 volt power cable. The AIS Engine 3 and a conventional marine antenna are all you need to start plotting vessels on your PC or AIS compatible plotter. The software runs in windows 95, 98, ME, XP, 2000, NT and Vista, ... Read more »

The Clipper navtex is the culmination of nearly 20 years of experience in manufacturing navtex instruments. The compact display unit will grace any instrument panel with its sharp high contrast liquid crystal display. Standard features of the receiver include 518 and 490kHz message reception and a non volatile program memory - if your sailing is confined to one particular area, then you need pr... Read more »

The BM-1 is designed to monitor performance of 12 volt lead acid battery systems with capacities of up to 600 Amp hours. It is supplied complete with a precision 100 AMP shunt and a prefabricated cable assembly to enable simple DIY installation. The unit continuously monitors voltage, current (charge or discharge), number of amp/hours (charge or discharge), the batteries state of charge and the... Read more »

Spare antenna with a 7 metre cable suitable for Clipper Navtex and Target Navtex 2 channel receivers It is not suitable for single frequency receivers - see 518Khz type. Read more »

The BM-1 is designed to monitor performance of 12 volt lead acid battery systems with capacities of up to 600 Amp hours. It is supplied complete with a precision 100 AMP shunt and a prefabricated cable assembly to enable simple DIY installation. The unit continuously monitors voltage, current (charge or discharge), number of amp/hours (charge or discharge), the batteries state of charge and the... Read more »

● The Target Navtex Pro is packed with features yet is still remarkably easy to install and use. Great care has been taken to make this unit very simple to operate, in fact should one lose the comprehensive instruction book supplied with it, it is possible to program the unit via the on-screen menus – it really is that simple. The messages are displayed on a high contrast backlit liquid crystal... Read more »

The BM-2 is designed to monitor performance of 12 volt lead acid battery systems with capacities of up to 999 Amp hours. It is supplied complete with a precision 200 AMP shunt and a prefabricated cable assembly to enable simple DIY installation. The unit continuously monitors voltage, current (charge or discharge), number of amp/hours (charge or discharge), the batteries state of charge and the... Read more »

♦ The new bluetooth Navtex is a dual frequency Navtex receiver that decodes and stores Navtex messages for viewing on an Android bluetooth enabled mobile phone or tablet. The unit is designed to be run continuously and have the stored messages downloaded as and when required by the user. An android app enables the user to search the stored messages or to program the device to display only ... Read more »

● The Target Navtex Pro is packed with features yet is still remarkably easy to install and use. Great care has been taken to make this unit very simple to operate, in fact should one lose the comprehensive instruction book supplied with it, it is possible to program the unit via the on-screen menus – it really is that simple. The messages are displayed on a high contrast backlit liquid crystal... Read more »

A high performance instrument system that shows almost instantaneous changes of wind speed and direction. In demanding conditions, where high performance is essential, the Clipper Tactical wind system is the ideal choice. With ten updates every second it responds very quickly to the changes in wind speed and direction, which occur during tricky manoeuvres. The sensor is supplied complete with a... Read more »

The Clipper Wind system shares the same 110mm square case as its sister instruments in the Clipper range. the display is exceptionally large and clear, with 60 segments for full 360 degree direction indication. Windspeed is shown in knots, M.P.H. or Metres/second. The pointer style is selectable, from the single segment shown above, to multi segments for greater clarity or a ‘windex’ style indi... Read more »

The Clipper wireless wind is supplied with a wireless masthead transmitter, a base unit and a Clipper Wind display unit. The wireless masthead transmitter is powered by an internal battery which is charged from ambient light using a small solar panel. A few dull days will not affect performance. When fully charged, it is capable of two thousand hours of full operation in total darkness. The mas... Read more »

Conventional navtex antennas respond to the electrical component associated with the navtex radio signal. They usually perform well at sea where electrical interference is low but can sometimes be overwhelmed with interference especially when in harbour and connected to shore power. In most small craft the electrical system acts as an effective ground for the antenna but it can also be a source... Read more »

♦ The new bluetooth Navtex is a dual frequency Navtex receiver that decodes and stores Navtex messages for viewing on an Android bluetooth enabled mobile phone or tablet. The unit is designed to be run continuously and have the stored messages downloaded as and when required by the user. An android app enables the user to search the stored messages or to program the device to display only ... Read more »

● Best selling depth sounder with giant 40 mm high digits for easy viewing. ● Supplied complete with in hull depth transducer with 7 metre cable.   Technical Features: ● Depth below transducer, below keel and below surface. ● Deep and shallow alarms (audible and visual) ● User selectable feet or meters. ● Intelligent gain control + manual overide. ● Selectable display rate and depth averaging r... Read more »

Clipper Wind Repeater / V2 – 3 wire mast unit display The Clipper Wind NMEA Repeater has user a selectable pointer style and selectable wind speed scale. It requires the standard NMEA 0183 MWV data sentence. (Supplied as standard equipment to the Clipper Wind V2 – 3 wire wind mast unit and the Clipper Wireless wind unit.) Technical Specifications • Consumption, 10mA+ (25mA for display illu... Read more »

• Complete with 10 meters of cable • Accuracy +/- 2 degrees • Gimballed to +/- 30 degrees • Output frequency 1Hz • Outputs NMEA 0183 sentence HDG • 12V supply • Dimensions 72mm x 68mm x 40mm • Weight 475 grams including 10-meter cable Read more »

Best selling combined Speed/Distance Log and Echo Sounder in standard 110mm square size. Suitable for open cockpit mounting. The Clipper Duet is supplied complete with a paddlewheel transducer (for installation on most types of GRP hulls) and in-hull depth transducer. Technical Specifications Depth Sounder in feet and meters. Shallow Alarm and Keel Offset. Complete with well-proven Transducers... Read more »

The BM-1 Li-battery monitor is designed explicitly for 12-Volt lithium iron phosphate (LiFePO4) battery installation. Capable of continuous charge or discharge currents of up to 100 Amps, BM-1 Li displays the service battery Voltage, the charge or discharge current, the state of charge, and the time to achieve full charge during charging or the time remaining during discharge. This information ... Read more »

BM-1 Bluetooth battery monitor BM-1 (BT) Bluetooth Battery Monitor for Android* When you need a battery monitor but don’t have space for the display or routing the cables would be a nightmare, there is now a solution. The BM-1(BT) will monitor your boat or caravan’s lead-acid batteries and transmit the data directly to your mobile phone or tablet wirelessly by Bluetooth. A simple Android app, f... Read more »